Language
 
 
Jeff Rowland Model 625 Stereo Power Amplifier
 
 

MODEL 625 STEREO

Precision machined from a single block of non-resonant aircraft-grade aluminum, the Model 625 features a unique composite circuit architecture incorporating separate Class AB voltage and current gain blocks with no overall negative feedback and virtually free of internal and external EMI field contamination and mechanical vibration.

The Model 625 delivers a sensuous grain-free musicality of unparalleled transparency and low level resolution that blossoms from a rich velvety silence and blossoms into the pure enjoyment of your listening experience.

MODEL 625 FEATURES

MACHINED ALUMINUM CHASSIS

Precision-machined chassis with integrated heat-sinks, milled from a solid block of aircraft grade aluminum, provides exceptional thermal heat transfer/dissipation, RFI/EMI shielding, and resonance control.

COMPOSITE CIRCUIT ARCHITECTURE

Unique composite circuit architecture incorporating separate Class AB voltage and current gain blocks with no overall negative feedback, delivers a sensuous grain-free musicality of unparalleled transparency and low level resolution.

BALANCED TOPOLOGY

Inherent cancellation effects of balanced topology implemented throughout all power and input/output circuits ensures greatly reduced distortion and noise under dynamic signal conditions.

HIGH-CURRENT COPPER BUS-BARS

High-current, dual polarity, ultra-low impedance copper bus-bars distribute both power supply input current and signal output current, virtually eliminating intra-circuit EMI signal contamination, greatly reducing internal wiring, while increasing circuit board rigidity.

HIGH-PRECISION SURFACE MOUNT COMPONENTS

Extensive use of Lead (Pb)-free, low  temperature coefficient, active and passive surface-mount components results in significantly smaller loop areas, reduced circuit capacitance and inductance, and introduces less noise than conventional leaded components.

TRANSFORMER-COUPLING AND ISOLATION

Transformer coupled input circuitry provides universal component compatibility and virtually eliminate ground loop noise and RFI/EMI. Transformer coupling ensures identical amplifier overall gain when using unbalanced input adapters.

POWER FACTOR CORRECTION

Power Factor Correction (PFC) in the power supply reduces AC line harmonic noise pollution and increases AC line power utilization to 99%

HIGH-EFFICIENCY SWITCH-MODE POWER SUPPLY

Highly efficient, compact, light weight, 1500 watt DC switch mode power supply provides optimum voltage regulation for all circuits and operating conditions, and allows for quiet operation over a wide range of AC mains power sources.

DUAL-POSITIONS SPEAKER TERMINALS

Dual CE approved speaker output terminals, in both horizontal and vertical orientation, require no tools for secure, low resistance connections, and allow for easy bi-wiring applications.

FLEXIBLE 20 AMP AC POWER

20 amp AC power inlet accepts a wide variety of after-market high-performance power cables.

FRONT-PANEL STANDBY BUTTON

Illuminated front panel push-button switches the amplifier into standby mode (<1watt consumption).

REAR PANEL REMOTE JACK

12V 3.5mm jack on rear panel permits amplifier power on/standby switching in remote and home theater applications.

SELF-LEVELING SUPPORTS

Removable 3-point self-leveling Delron chassis supports provide high frequency mechanical noise isolation.

MODEL 625 SPECIFICATIONS

Output Power: 300 watts @ 8 ohms / 550 watts @ 4ohms

Frequency Response: 5 Hz – 350 kHz

S/N Ratio: 95 dB, ref. 1.0 watt @ 8 ohm load

Output Noise: <55 uv, 20Hz – 20kHz, unweighted

Crosstalk: >91 dB @ 1 kHz, 74 dB @ 20kHz

Input Impedance: 10k ohms

THD + Noise: 0.005% @ 1kHz, 8 ohms

Damping Factor: >200, 20 Hz – 20 kHz

Overall Gain / Bal. or Unbal.: 27dB

Common Mode Rejection Ratio: >90dB, 20 Hz – 20 kHz

Absolute Phase Non-inverting: Pin 2 Positive

Inputs: 1 pair balanced (XLR)

Output: 2 pair parallel binding posts per channel

Power Consumption Idle: 100 watts

Power Consumption Standby: 1 watt

Amplifier Weight: 54 lbs. / 24.5 kg

Amplifier Shipping Weight: 64 lbs. / 29 kg

Amplifier Dimensions (h/w/d): 5.75” x 15.5” x 16.25” / 146mm x 394mm x 413mm

For more information : 

Contact : Dicky Ng 012-3308893

Email : dickyng@cmy.com.my

Available Options:
Stock Availability : Available
Qty :
 

 
 
Copyright © 2016 CMY Audio & Visual. All Rights Reserved.